|Replacement Parts||Bridge Power Adapter: 5N1ADPTR|
Tower Sensor: 11126-592TXR
Dimensions: 8.8-inch Height x 3.4-inch Width x 1.9-inch Depth
Dimensions: 5-inch Height x 3.5-inch Width x 5-inch Depth
TEMPERATURE & HUMIDITY SENSOR Outdoor Temperature Range: -40 to 158 degrees Fahrenheit, -40 to 70 degrees Celsius Temperature Accuracy: +/- 2 degrees Fahrenheit; Learn more
TEMPERATURE & HUMIDITY SENSOR
Outdoor Temperature Range: -40 to 158 degrees Fahrenheit, -40 to 70 degrees Celsius
Temperature Accuracy: +/- 2 degrees Fahrenheit; Learn more
|When adding my smartHUB to my account, it's not recognized|
When power was first applied to the smartHUB, it attempts to connect to your network to activate its Device ID with My AcuRite. Once activated, it can be added to your account.Possible solutions
Allow up to ten minutes for the smartHUB Device ID to be activated with My AcuRite.
Make sure the Device ID was entered correctly. Verify the 12-character Device ID located on the bottom side of the smartHUB and re-enter.
Verify the smartHUB has a network (Internet) connection. If the Network Status Light flashes rapidly in 30 second intervals, this indicates is does not have an Internet connection.
Unplug the smartHUB power adapter, wait ten seconds and then plug back in.
|No sensors are listed in Available Sensors|
When there are no sensors listed in Available Sensors, it indicates there are no sensors in wireless range of the smartHUB, or the sensors are already linked to the smartHUB and listed in My Sensors.Possible solutions
If the sensor was just powered on or was recently moved to be in wireless range, it can take up to a minute to be available.
If you are using a smartHUB, no Available Sensors is commonly caused by one of the following reasons:
|My smartHUB does not have a network (internet) connection|
When the Network Status Light flashes rapidly in 30 second intervals, the smartHUB cannot establish a network (Internet) connection.
NOTE: When working normally, the smartHUB network status light flashes for 1 second each time a reading is sent to My AcuRite.
Make sure the Ethernet cable is firmly connected. The cable may be defective and need to be replaced.
Make sure DHCP is enabled on your router. Most routers have DHCP enabled by default.
Check your network router settings. If MAC address filtering security has been enabled, your router may be ignoring the outbound communication from the smartHUB. Review the network router manual or contact the manufacturer for more information. NOTE: The smartHUB Device ID is its MAC address.
The Ethernet port on your router may be malfunctioning. Try connecting the cable to a different port.
|My smartHUB sensor status light is continuously flashing rapidly|
When the Sensor Status Light is continuously flashing rapidly, the smartHUB has not received a sensor reading for more than 60 seconds.Possible solutions
Make sure the sensor is in wireless range of the smartHUB, A sensor must be located no more than 330 feet (100 meters) from the smartHUB or PC Connect Display.
Make sure the sensor batteries are installed correctly and the sensor is powered. You may need to replace the sensor batteries.
Make sure the smartHUB is located at least 3 feet away from "noisy" electronic devices, including TVs and microwaves. Avoid locations that are near large stone or concrete surfaces and metallic surfaces.
|Why are the pressure measurements different in My AcuRite compared to my Indoor Display?|
The AcuRite Environmental Weather Stations and My AcuRite use different methods to adjust the barometric pressure for altitude. These methods may result in small differences in pressure readings.Weather Station barometric pressure measurement method
Weather Stations use a unique algorithm to analyze changes in pressure over a time period, referred to its Learning Mode, to determine the altitude. A Weather Station displays the barometric pressure reading that has been adjusted by this algorithm.My AcuRite barometric pressure measurement method
My AcuRite uses the geo-location of the address or Postal Code set in the profile of a smartHUB or PC Connect Display in your My AcuRite account. The barometric pressure altitude is adjusted to the address or Postal Code location. This method does not require a Learning Mode.
|How do I check the last time a reading of a sensor was sent to my account?|
The status color indicator next to the name of the sensor is a quick way to determine its current status. Select the indicator to view more information about the status of the sensor.
Green - everything is operating as expected.
Yellow - a condition may need your attention soon and should be looked into.
Red - a condition does need your attention now.
Questions? We're here to help. Phone +1-262-729-4852 | My AcuRite Technical Support +1-262-729-4850 | Community forum: http://support.acurite.com
Questions? We're here to help.
Phone +1-262-729-4852 | My AcuRite Technical Support +1-262-729-4850 | Community forum: http://support.acurite.com