You have no items in your shopping cart.


Product was successfully added to your shopping cart.
Knowledge Base, Manuals & Downloads

01506 / 01524 / 01534 / 06025 Weather Station

01506 AcuRite Professional Weather Center

Manual AcuRite Professional Weather Center Instruction Manual  [PDF]
Sensor Installation 5-in-1 sensor installation
Icon Definitions Click here
Replacement Parts Add-on or Replacement Display: 06025RM
Replacement Power Adapter: 1524589AD

5-in-1 PRO Weather Sensor: 06014RM
5-in-1 Weather Sensor: VN1TXC
PRO+ Upgrade for the 5-in-1 Sensor: 5N1DSSA
Replacement 5-in-1 Sensor Wind Cups: 5N1WC / 06031RM
Replacement 5-in-1 Sensor Wind Cups Assembly (with Bearings): 5N1WCBSA
Replacement 5-in-1 Sensor Wind Vane: 5N1VANE
Replacement 5-in-1 Sensor Mounting Bracket: 5N1MB
Mounting Tripod for Environmental Sensors: 06055M



Dimensions: 7.7-inches Height x 7.1-inches Width x 1.3-inches Depth
Indoor Temperature Range: 32º to 122º F, 0º C to 50º C
Humidity Range: 1% to 99% RH
Data Reporting: Indoor data: 60 second updates
Power: 5V AC Adapter (included), 6 AA alkaline batteries


Outdoor Temperature Range: -40º to 158º F, -40º C to 70º C
Outdoor Humidity Range: 1% to 99% RH
Wind Range: 0 to 99 mph
Rainfall Measurement: Measures 0.01 inches (0.25 mm) and up
RF (wireless) Range: 330 feet (100 meters)
Data Reporting: Wind Speed: 18 second updates; Wind Direction, Temperature & Humidity: 36 second updates
Wireless Frequency: 433 MHz
Power: 4 AA alkaline or lithium batteries; Lithium batteries recommended for temperatures below -4°F/-20ºC


Temperature Accuracy: +/- 2 degrees Fahrenheit; Learn More
Humidity Accuracy: +/- 5%
Wind Speed Accuracy: up to +/- 5mph
Rainfall Accuracy: +/- .05" per inch

Problem Possible Solution
is flashing or
showing dashes
Flashing of the outdoor temperature may be an indication of wireless interference.
• Make sure the A-B-C switch in the battery compartments of both the display unit and sensor are switched to the same letter. You may choose A, B or C; but both units must match to sync up. Sometimes changing to a different channel can help.

No outdoor 

• Relocate the display unit and/or the 5-in-1 sensor. The units must be within 330 ft (100 m) of each other.
• Make sure both units are placed at least 3 feet (.9 m) away from electronics that may interfere with the wireless communication (such as TVs, microwaves, computers, etc).
• Use standard alkaline batteries (or lithium batteries in sensor when temperature is below -4ºF/-20ºC). Do not use heavy duty or rechargeable batteries. NOTE: It may take up to 20 minutes for display unit and sensor to synchronize after batteries are replaced.
• Synchronize the units:
1. Bring both the sensor and display unit indoors and remove at least one battery from each.
2. Make sure the A-B-C switch on both units match. Sometimes changing to a different channel can help.
3. Reinstall the battery in the outdoor sensor.
4. Reinstall battery into the display unit.
5. Let the units sit within a couple feet of each other for about 20 minutes to gain a strong connection.
• Weather Forecast icon predicts conditions for the next 12 to 24 hours, not current conditions.
• Has Learning Mode icon disappeared from the display unit? Learning Mode must complete before forecast and pressure will be accurate.
• Allow unit to run continuously for 33 days. Battery removal or resetting the display unit will restart Learning Mode. After 14 days, forecast should be fairly accurate, however Learning Mode calibrates for a total of 33 days.
or humidity

• Make sure both the display unit and 5-in-1 sensor are placed away from any heat sources or vents.
• Make sure both units are positioned away from moisture sources.
• Make sure 5-in-1 sensor is mounted at least 5 ft off of the ground.
• Calibrate indoor and outdoor temperature and humidity.

  1. To access calibration mode, press AND HOLD the ▲ and ▼ buttons simultaneously for 5 seconds.
  2. To adjust the currently selected (flashing) item, press and release the ▲ or ▼ buttons to calibrate the data value higher or lower from the actual reading.
  3. To save your adjustments, press and release the "SET" button to adjust the next preference.
No rainfall

• Be sure the plastic tab under the rain collector (put in place for shipping purposes) on the bottom of the 5-in-1 sensor has been removed.
• Make sure the 5-in-1 sensor's internal tipping lever is able to move freely by dripping a small amount of water through the rain collector. You should be able to hear the lever tipping.

Items Needed: 5-in-1 sensor, Philips screwdriver, damp cloth, car wax, toothbrush (optional), moth ball (optional)

1.  First, open your 5-in-1 sensor by removing the (4) four screws from the bottom. The screws toward the center of the sensor are for Rain Gauge calibration only. Do not adjust these screws.
2.  After your sensor has been opened, remove any insects, cobwebs, or debris. An old toothbrush can help to clean out the hard-to-reach places.
3.  Use a damp cloth to clean off the rain gauge tipping buckets. 
Note: The damp cloth should only be used to clean the tipping buckets. Do not use to clean any other internal components.
4.  Place a small amount of car wax on a soft cloth and wipe down the tipping bucks to ensure that rain flows through smoothly.
5.  To further defend against insects crawling into your sensor, you may place a moth ball in the nook, near the tipping buckets (shown in video). Adhere the moth ball to the sensor with a piece of tape. 
Note: Insect repellant may be used for additional protection, but should not be sprayed on the internal components or into the sensor.
6.  Reassemble the 5-in-1 sensor by replacing the (4) four screws on the bottom of the sensor that were removed earlier.
7.  Clear out any false readings that were taken while you were cleaning your sensor by pressing the CLEAR TODAY button on your 5-in-1 compatible display.

Inaccurate rainfall

The rain gauge on the 5-in-1 sensor can be calibrated to improve accuracy by following the directions below.
Items Needed: 5-in-1 sensor, display console, plastic cup, pin, screw driver

1.  First, make sure the 5-in-1 sensor is perfectly level using the built-in bubble level.
2.  Place the display console close by so you can monitor it during the calibration process.
3.  Make a pin hole in the bottom of a plastic cup.
Hold the cup over the rain gauge and fill it with exactly 1 cup (8 oz.) of water, allowing the water to drip into the rain gauge. You should hear the internal buckets tip and see the water drain through the rain gauge.
4.  A few seconds after each bucket tip, the display console will display rainfall in approximately 0.01" or more increments.
5.  The cup of water should take more than 20 minutes to empty; a quicker period will result in an inaccurate calibration. (We’re trying to simulate a normal steady rainfall.) When the cup is completely empty of water, the display console should register 1.06"

If the rain gauge doesn't register close to 1.06" after the cup is empty of water, then you should make an equal adjustment to the two calibration screws on the bottom of the 5-in-1 sensor. Be sure to adjust both screws the same amount. Turning screws clockwise will increase rainfall amount. Turning screw counter clockwise will decrease it.

To adjust the rainfall reading by 2% turn both screws 1/8  of a turn
To adjust the rainfall reading by 4% turn both screws 1/4 of a turn.
To adjust the rainfall reading by 8% turn both screws 1/2 of a turn.

• There should be nearly an equal number of water drops (typically about 25 water drops) between bucket tips. If not, then adjust the calibration screws on the bottom of the 5-in-1 sensor until an equal number of water drops are tipping the buckets. Then, restart the calibration procedure.

• If you don't hear the buckets tipping and see water dripping alternately out of each drain, there may be an issue with the rain gauge or it's adjustment. Contact Customer Support.
Inaccurate wind
• What is wind reading being compared to? Pro weather stations are typically mounted at 30 ft high or more. Make sure to compare data using a sensor positioned at the same mounting height.
• Check location of the sensor. Ensure it's mounted a minimum of 5 ft in the air with no obstructions around it (within several feet).
• Ensure wind cups are spinning freely. If they hesitate or stop, try lubricating with graphite powder or spray lubricant.
How to Mount
the 5-in-1 Sensor
• Mount the sensor at least 5 ft off the ground (higher is better for accurate wind measurements) in an open area NO FURTHER than 330 feet (100 meters) from the display console. A typical installation would involve mounting the bracket to a secured length of 2 x 4 or 4 x 4 wood, 3/4" pole, etc. (not included). For more information, visit: www.acurite.com/5in1
Display screen
not working
• Check that the batteries are installed correctly.
Batteries may need to be replaced.
• Reset the display by pressing and HOLDING the "CLEAR RECORD/RESET" button, located on the back of the display unit. Date and time will need to be entered after a reset.


Questions? We're here to help.

Phone +1-262-729-4852  |  My AcuRite Technical Support +1-262-729-4850 |  Community forum: http://support.acurite.com

Models: 01506, 01524, 01524A1, 01524DI, 01524DIA1, 01524M, 01524MWW, 01534DI, 06025RM, 06025M




install the AcuRite 5-in-1 weather sensorInstall the 5-in-1 Weather Sensor

Step-by-step directions with video to set up your 5-in-1 weather sensor for maximum accuracy.

install the AcuRite 3-in-1 weather sensorInstall the 3-in-1 Weather Sensor

Step-by-step directions with video to set up your 3-in-1 weather sensor for maximum accuracy.

maximize wireless range troubleshootingGet the Best Wireless Range

Maximize the wireless range of AcuRite's 433 MHz wireless technology for superior performance.

how to site a weather sensorSensor Siting to Maximize Accuracy

Sensor siting helps install your sensors in the way that best captures the data that is most important to you.

acurite battery requirementsBattery Requirements for AcuRite Products

AcuRite recommends new, high quality, name brand alkaline batteries for the best product performance.