You have no items in your shopping cart.


Product was successfully added to your shopping cart.
Knowledge Base, Manuals & Downloads

13022 / 13035W Alarm Clock

13022 AcuRite Alarm Clock


Atomic Dual Alarm Clock with USB Charging & Temperature Instruction Manual 13022 / 13035  [PDF]

Replacement PartsOutdoor Sensor: 592TXR
Power Adapter: ALARMADPT
More InformationAtomic Technology
SpecificationsTime Zones: HAST, AKST, EST, PST, MST, CST, EST, AST
Outdoor Temperature Range: 32° to 122° F, 0° C to 50° C
Temperature Accuracy: +/- 2°F
RF (wireless) Range: 330' (100m)
Data Reporting: Outdoor data: 16 second updates; Indoor data: 30 second updates
Power: Display: 5V AC power adapter (included; recommended for optimal display color), 3 AA alkaline batteries (optional; not included) Sensor: 2 AA alkaline or lithium batteries* (not included) *Lithium batteries recommended for temperatures below -4°F/-20ºC

ProblemPossible Solution

Clock is too dark,
hard to read or
doesn't work

• The backlight may automatically turn off for 10 minutes at 2:00am and 3:00am to acquire the atomic signal. 
• Verify power adapter is plugged in.
• Check that the batteries are installed correctly. Batteries may need to be replaced.
• Increase brightness using the dimmer control, located on the back of the clock.
• The optimum viewing angle for this product is from slightly above it.
• Reset the unit by pressing the reset button, located in the battery compartment.

No outdoor sensor

If the wireless signal indicator shows no bars:
• Relocate the clock and/or outdoor sensor. The units must be within 330 ft (100m) of each other.
• Make sure both units are placed at least 3 feet (.9m) away from electronics that may interfere with the wireless communication (such as TVs, microwaves, computers, etc.)
• use standard alkaline batteries (or lithium batteries in sensor when temperature is below -4°F/-20°C). Do not use heavy duty or rechargeable batteries. NOTE: It may take up to 20 minutes for clock and sensor to synchronize after batteries are replaced.

flashing or
showing dashes

Flashing of the outdoor temperature is generally an indication of wireless interference.• 1. Bring both the sensor and clock indoors, side by side and remove batteries from each.
2. Make sure the A-B-C switch on both units match.
3. Reinstall batteries in outdoor sensor.
4. Reinstall batteries in clock.
5. Let the units sit within a couple feet of each other for about 20 minutes to gain a strong connection.


• Make sure the clock and sensor are placed out of direct sunlight and away from any heat sources or vents.

Atomic signal or time
syncing problems

For additional troubleshooting, please visit: http://www.nist.gov/pml/div688/grp40/radioclocks.cfm 

How long does snooze
disable the alarm?

• Snooze function disables alarm for 8 minutes.
• Snooze function can be activated up to 6 times. After the 6th time, the alarm will no longer sound.


Questions? We're here to help.

Phone +1-262-729-4852  |  My AcuRite Technical Support +1-262-729-4850 |  Community forum: http://support.acurite.com

Models: 13022 / 13035w




install the AcuRite 5-in-1 weather sensorInstall the 5-in-1 Weather Sensor

Step-by-step directions with video to set up your 5-in-1 weather sensor for maximum accuracy.

install the AcuRite 3-in-1 weather sensorInstall the 3-in-1 Weather Sensor

Step-by-step directions with video to set up your 3-in-1 weather sensor for maximum accuracy.

maximize wireless range troubleshootingGet the Best Wireless Range

Maximize the wireless range of AcuRite's 433 MHz wireless technology for superior performance.

how to site a weather sensorSensor Siting to Maximize Accuracy

Sensor siting helps install your sensors in the way that best captures the data that is most important to you.

acurite battery requirementsBattery Requirements for AcuRite Products

AcuRite recommends new, high quality, name brand alkaline batteries for the best product performance.