This article was initially published in 2018. We’ve updated it in March of 2024 to include more in-depth information and up-to-date cleaning tips.
Springtime is here, which means the friendly welcoming of daffodils and tulips and potentially the not-so-friendly welcoming of spring cleaning. But fear not! While this article cannot help you sweep your garage or organize your junk drawer, it can absolutely help if you’re looking to spruce up your weather station this spring! Whether you have the AcuRite Atlas® or AcuRite Iris™ (5-in-1), the below steps, tips, and tricks will help you measure your true backyard weather conditions, as seen on your indoor display or My AcuRite® app.
1) Check Rain Bucket to Ensure Proper Rainfall Measurement
Is your rain gauge reporting 0 inches of rain when it has been raining all day? If so, your rain gauge may be clogged, preventing the internal tipping cups from doing their job and recording rainfall.
If you have an AcuRite Atlas, follow these steps to clean your rain gauge sensor:
- Remove the batteries from your AcuRite Atlas outdoor sensor and detach the black rain bucket from the bottom half of the sensor.
- Remove any insects, cobwebs, or debris in the sensor and rain bucket using an old toothbrush for hard-to-reach places.
- Use a damp cloth to clean off the internal tipping cups and drip pan.
- Place a small amount of car wax on a soft cloth and wipe the tipping cups to help ensure rainwater flows through smoothly.
- Reattach the rain bucket to the bottom of the AcuRite Atlas outdoor sensor and reinstall the batteries.
Pro Tip! — To defend against insects crawling into your AcuRite Atlas, use tape to place a mothball in the nook near the tipping cups. For additional information, visit this AcuRite Atlas No Rainfall support page.
If you have an AcuRite Iris (5-in-1), follow these steps to clean your rain gauge sensor:
- Open your AcuRite Iris outdoor sensor by removing the four outside screws from the bottom of the unit (note: the near-the-center screws are only for rain gauge calibration).
- Remove any insects, cobwebs, or debris in the sensor using an old toothbrush for hard-to-reach places.
- Use a damp cloth to clean off the internal tipping cups.
- Place a small amount of car wax on a soft cloth and wipe the tipping cups to help ensure rainwater flows through smoothly.
- Reassemble your AcuRite Iris by replacing the four screws.
Pro Tip! — To defend against insects crawling into your AcuRite Iris, use tape to place a mothball in the nook near the tipping cups. For additional information, visit this AcuRite Iris No Rainfall support page.
Important to Remember!
Removing the batteries from your weather station (or the rain gauge if you have the stand-alone unit) eliminates the chance of sending any erroneous rainfall measurements to your My AcuRite dashboard.
2) Check Wind Cups and Anemometer to Ensure Accurate Wind Information
To receive hyperlocal wind information, it’s imperative to make sure your cup anemometer and wind vane are able to spin freely. Clear out any visible dirt, dust, or debris with a damp rag or paper towel. In colder climates, freezing rain or ice can freeze these instruments and restrain them from spinning, so be sure to check after any early spring storms!
If any parts are cracked, broken, or not spinning freely after cleaning, you can order new wind cups for the AcuRite Atlas, AcuRite Iris, and AcuRite Notos®. You can also order a replacement wind vane for the AcuRite Atlas and AcuRite Iris directly from AcuRite. If ordering new parts, check out the lightning sensor or wind extension to add a new feature to your weather station!
Pro Tip! — After cleaning, make sure your outdoor sensor is mounted at least 5 feet in the air without any surrounding obstructions for the most accurate wind speed and wind direction measurements. While the National Weather Service recommends mounting wind measurement instruments 33 feet or higher without obstructions within 100 feet, we recognize that not everyone has the means to do so. However, know that your AcuRite weather station will provide an accurate reading for the location your sensor is mounted.
3) Clean Solar Panels to Ensure Correct Temperature and Humidity Measurements
Your solar panels should be cleaned regularly to provide the most factual temperature and humidity measurements possible. When the solar panels are dirty or dusty, your weather station’s internal fan (to disperse radiant heat) doesn’t receive maximum power, which can impact the temperature and humidity data you receive. Use a warm, damp rag or paper towel with gentle soap to wipe them clean.
Pro Tip! — For the highest accuracy and efficiency, the solar panel (or panels if you have a dual-sensor AcuRite Iris or AcuRite Atlas) should face due south if used in the Northern Hemisphere and due north if used in the Southern Hemisphere.
4) Maintain Your Weather Station Year-Round!
Keeping your AcuRite Atlas, AcuRite Iris, or AcuRite Notos as clean as possible will extend its life and help to provide you with the most accurate weather measurements. At least twice a year, we recommend cleaning off the entire unit using a damp rag, a little soap, and warm water. This should clear the bugs, spiders, and spider webs away from any inlet areas.
Cleaning your weather station is also a great time to install fresh batteries. We recommend using lithium batteries if your weather station experiences outdoor temperatures below -4 °F (-20 °C) and alkaline batteries for weather stations in areas routinely above that mark. While we expect these recommended batteries to last 12-24 months, we’d err on the side of caution and replace them at least every 12 months or sooner if you experience a lack of weather readings on your indoor display.
Pro Tip! — For safety, always clean the battery contacts and compartments before installing batteries. Also, be sure to dispose of your used batteries in an environmentally safe way by following your local laws and regulations!
Happy Spring Cleaning!
We hope these steps, tips, and tricks will help you tidy up your AcuRite weather station this spring! While spring cleaning is important, your weather station could benefit from a little TLC at any point of the year to continue providing you with the most precise hyperlocal weather information. If you’ve followed the above steps and still require assistance, visit our support website for helpful articles and the opportunity to start a live chat with one of our local employees. Happy spring!
P.S. Bonus Tip for the Temperature and Humidity Sensors!
If you have one of our weather stations with an outdoor temperature and humidity sensor and notice inaccurate readings, your sensor may be placed too directly in sunlight! An AcuRite radiation shield will shade the sensor from the sun, resulting in more accurate temperature and humidity readings from measuring the continuous flow of ambient air. The same goes for our lightning sensor, which also measures temperature and humidity. But be sure to inspect and clean the radiation shield regularly, because it’s a great place for bugs, spiders, and cobwebs to hide!
48 comments
We live in the southern hemisphere. Therefore the solar panels have to face north. As a result, the wind directions are incorrect. Is there any way to change the settings.
I had really bad problems with spiders inside mine and did the moth ball trick which works for maybe a month. I came up with the bright idea to use a small piece of the dogs flee collar, walla at least a yrs protection+. I use a piece about 2-3" long. It doesn’t have to be taped in or anything, it will stay in place.
I read where it is recommended to also spray the weather station with a spray on wax to protect the plastic. Do you still recommend this?
What lubricant do you recommend for the wind guage?
I’m a firm believer that of all the elements the 5 in 1 or Atlas measures, the wind speed and direction has to be the most challenging when comparing data with official NWS (such as the nearest airport). Wind speed readings from official NWS has their equipment in wide open spaces and usually at their standard 33ft elevation from ground level. If you have a 5 in 1 or Atlas in your backyard and live in a sub-division, you are likely to have obstructions such as trees, housing, etc. to block/reflect the wind causing wind speed to be lower and wind direction to be more variable than compared to the NWS.
Hi, looks nice. How can grab a home weather station in India. Do you ship it to india? or do you have local distributors here? thank you
I have wasps inside the unit that are preventing rainfall measurements. Can I spray wasp killer up underneath to kill wasps before cleaning it out? or will this damage sensors?
Mine is noisy & rain readings are wrong. Before I take it down, will cleaning the inside correct the noisiness?
My weather station emits a steady, rapid clicking sound. The rapidity of the clicking is constant, regardless of wind speed. Any ideas?
The solar panels on my 5-in-1 seem to be opaque and a film is peeling off. I’ve tried cleaning them with soap and water but that doesn’t have any effect. I think they are not putting out any energy as the batteries are draining quickly. Can the solar panels be replaced?
As someone who lives in a northern climate (Canada), with lots of snow and sub freezing temperatures for 4-5 months of the year, are there any special precautions/prep/maintenance that should be performed? I own an Atlas.
We live on the coast in central Oregon. Our 5 in 1 is subject to a lot of salty air from the sea. I have replaced the 5 in 1 twice due to the wind components rusting. I would suggest you replace those parts with a good quality stainless shaft and fittings.
My temperature reading is way off on a sunny day and about right in the evening and on a cloudy day. Doesn’t appear to have any debris internally and the batteries have been changed. Any suggestions other than get a replacement unit?
Is there any way to post edit the MyAcurite data? Right around 6AM this morning my rain gauge recorded a .65 inch data anomaly. It was not raining and no one was watering the plants near it at the time. I would like to remove the .65 inches of rain that appears to be one bad data point.
I have 2 (two) 5 in 1 Acurite weather stations, located at 2 different residences. Both have anemometer issues: they don’t seem to be spinning as easily in low wind speeds. In fact lower wind speeds fail to move the wind cups.
No debris buildup noted or cup deformity seen. Unit is still level and nothing is remotely close to interfering with cup rotation. I see comments regarding lubrication; Is lubrication just be done by spraying up under the cup post or can the 3 cup unit be removed and cleaned, bushing or bearings to be serviced or replaced.
Thanks
A recent storm brought sustained winds reading 40mph and gusts up to 55mph. There was no rain, yet the device recorded 7.9in of rain. Is there anything I can do to prevent high winds from altering the rain data?